Polyurea waterproofing of a drinking water tank in Barcelona

Polyurea sprayed over the tanks of a water treatment plant

Hot-spray polyurea waterproofing of the concrete tanks and channels of a water treatment plant in Barcelona: moisture control, epoxy primer and a continuous membrane.

Área metropolitana de Barcelona · Barcelona· 2025
Assess a similar project
Concrete tank waterproofed with a grey polyurea membrane at a Barcelona water treatment plant
Tank basin with the finished polyurea membrane: continuous, with no joints or overlaps.
Project data

Technical sheet

Instalación
Drinking water treatment plant, extension works
Elementos
Reinforced concrete roofs, basins and channels
Sistema
Tecnopol EPw-1070 epoxy primer + hot-spray polyurea membrane
Prior check
Substrate moisture measured point by point with a Tramex CME4 meter
Detailing
Wall penetrations and openings made good with mortar before the membrane
Resultado
Continuous membrane, with no joints or overlaps, on walls and slabs
Año
2025
Aplicación
Approved applicator from our network, under our technical direction

Polyurea waterproofing of drinking water tanks

During the extension of a drinking water treatment plant in the Barcelona metropolitan area, the concrete roofs, basins and channels were waterproofed with hot-spray polyurea. It is a continuous membrane with no joints or overlaps that cures in seconds and puts the tank back in service very quickly. For data protection reasons we do not publish the owner or the exact location.

Why polyurea in hydraulic works

  • Continuous, elastic membrane that follows concrete movement and bridges cracks.
  • Almost instant curing: it can be walked on and inspected within minutes, without stopping the works for days.
  • Full bond to the substrate if preparation is respected: no water under the membrane.

How we work: from enquiry to handover

On every project we take on whatever is needed, a single phase or the whole process:

  1. Technical enquiry. We receive photos, drawings and the problem, and reply with an initial assessment.
  2. Consulting and diagnosis. Site visit, testing and choice of the right system for the substrate and use.
  3. Specification and fixed-price quote for materials and execution.
  4. Execution by an approved applicator from our network, trained and approved by the system manufacturer.
  5. Site management and quality control: substrate, moisture, thickness, curing and detailing.
  6. Finishing, final documentation and handover.

Double guarantee: the manufacturer backs that the installed system meets its standards, and we guarantee it has been applied correctly. That is why our repairs, waterproofing and floors last for years.

Step by step

How a water tank is waterproofed with polyurea

  1. Tramex CME4 moisture meter on a tank's concrete before priming
    Step 1

    Measure substrate moisture

    Concrete moisture is measured with a meter across the whole surface. If the substrate is not dry, it is not primed.

  2. Worker making good a wall penetration with mortar before waterproofing
    Step 2

    Make good the details

    Penetrations, openings and honeycombing are made good with mortar before applying the membrane.

  3. Roller-applied epoxy primer on the concrete roof of a water tank
    Step 3

    Prime with epoxy

    Tecnopol EPw-1070 epoxy primer is roller-applied to seal the pores and anchor the membrane.

  4. Worker hot-spraying polyurea at the wall-to-slab junction of a water tank
    Step 4

    Hot-spray the polyurea

    A two-component rig sprays junctions and corners first, then the main areas, until a continuous membrane is formed.

  5. Concrete tank waterproofed with a grey polyurea membrane at a Barcelona water treatment plant
    Step 5

    Check continuity and thickness

    The whole surface is checked before handover.

On-site record

Project photos and video

Wall-to-slab junction of a concrete tank waterproofed with polyurea
Wall-to-slab junction with the membrane carried up the wall.
Hot-spray polyurea rig inside a workshop truck on site
Two-component hot-spray rig in a workshop truck on site.
Spraying polyurea on wall and slab (23 s, no sound).
Common questions

Frequently asked questions

Why polyurea to waterproof a water tank?

Because it forms a continuous, elastic, jointless membrane that cures in seconds, so the tank is back in service very quickly.

What happens if the concrete is damp when polyurea is applied?

Adhesion fails and blisters or delamination appear. That is why we measure substrate moisture before priming and never apply on damp concrete.

Can polyurea be used in drinking water tanks?

Yes, as long as the system is certified for contact with drinking water. We check the manufacturer's data sheet before specifying it.

Who carries out the work?

An approved applicator from our network, trained and approved by the system manufacturer. We handle the consulting, the specification and site management, and we guarantee the system is properly applied.

Do you work outside Catalonia?

Yes. We work throughout Spain, especially in Catalonia, the Valencia region and Aragon, with approved applicators in each area.

Do you have tanks, ponds or channels to waterproof?

Send us drawings or photos: we specify the system, an approved applicator installs it and we manage the work through to handover, anywhere in Spain.

Request a technical study
Call WhatsApp Request a quote