Crack and joint repair of a water tank in La Bisbal d'Empordà

Water tank cracks and joints sealed and watertight

Sealing of cracks in concrete walls and of the base joint of a water tank in La Bisbal d'Empordà (Girona), with mesh-reinforced waterproofing mortar.

La Bisbal d'Empordà · Girona· 2025 project
Assess a similar project
Concrete water tank wall with a crack repaired with white waterproofing mortar
Wall crack repaired: band of reinforced waterproofing mortar over the tank's dark coating.
Project data

Technical sheet

Instalación
Outdoor reinforced concrete water tank with a dark coating
Problema
Vertical cracks in the walls and a leaking horizontal base joint
Fisuras
Opened with an angle grinder, cleaned out and sealed in depth
Base joint
Routed with dust extraction, sealed and bridged with waterproofing
Impermeabilización
Flexible waterproofing mortar in two coats, reinforced with glass fibre mesh
Sistemas
Waterproofing mortars and sealants (SikaTop® and Sikaflex® type ranges)
Año
January 2025
Aplicador
From our network, approved by the manufacturer

Repairing a water tank in La Bisbal d'Empordà

A reinforced concrete water tank in La Bisbal d'Empordà (Baix Empordà, Girona) was losing water in two ways: vertical cracks in the walls and the horizontal joint between slab and wall, where leak stains were visible from outside. For data protection reasons we do not name the owner of the facility.

Crack by crack, not a coat of paint

Each crack was opened with an angle grinder, cleaned out and sealed in depth. It was then bridged with a flexible waterproofing mortar reinforced with glass fibre mesh, in two coats, so it follows the wall's small movements without opening again. The base joint was routed with dust extraction, sealed and reinforced with the same waterproof band.

Why tank joints and cracks fail

  • Shrinkage and temperature: the concrete moves and the crack opens and closes.
  • Construction joint between slab and wall poorly executed from the start.
  • Water pressure: what starts as damp ends up as a leak and reinforcement corrosion.

How we work: from enquiry to handover

On every project we take on whatever is needed, a single phase or the whole process:

  1. Technical enquiry. We receive photos, drawings and the problem, and reply with an initial assessment.
  2. Consulting and diagnosis. Site visit, testing and choice of the right system for the substrate and use.
  3. Specification and fixed-price quote for materials and execution.
  4. Execution by an approved applicator from our network, trained and approved by the system manufacturer.
  5. Site management and quality control: substrate, moisture, thickness, curing and detailing.
  6. Finishing, final documentation and handover.

Double guarantee: the manufacturer backs that the installed system meets its standards, and we guarantee it has been applied correctly. That is why our repairs, waterproofing and floors last for years.

Step by step

How the cracks and joints of a water tank are repaired

  1. Vertical crack in a water tank's concrete wall marked in red
    Step 1

    Locate and mark

    The walls are walked, leaking cracks and joints are located and marked.

  2. Worker opening a crack in a tank's concrete wall with an angle grinder
    Step 2

    Open and clean out

    Each crack is opened with an angle grinder and the base joint routed, with dust extraction, back to sound concrete.

  3. Sealing a crack in a concrete wall with a cartridge gun
    Step 3

    Seal in depth

    The opened crack is sealed from a cartridge and levelled with a spatula.

  4. Glass fibre mesh embedded in waterproofing mortar over a crack
    Step 4

    Reinforce with mesh

    First coat of waterproofing mortar with embedded glass fibre mesh, which absorbs small movements.

  5. Worker trowelling waterproofing mortar onto a tank wall
    Step 5

    Impermeabilizar

    Second coat of waterproofing mortar by trowel until the whole band is covered.

  6. Concrete water tank wall with a crack repaired with white waterproofing mortar
    Step 6

    Check watertightness

    Each crack and the joint are checked with the tank full.

On-site record

Project photos

Levelling the crack sealant with a spatula on a tank wall
Sealant levelled with a spatula.
Horizontal joint at the base of a water tank with leak stains
Horizontal base joint with leak stains: the tank's other defect.
Crack opened and cleaned out in a water tank's concrete
Crack opened and cleaned back to sound concrete.
Worker routing the tank's base joint with an angle grinder and dust extraction
Base joint routed with dust extraction.
The approved applicator's team working on the water tank wall
The team of the approved applicator from our network on site.
Water tank base joint repaired with waterproofing mortar
Base joint repaired and watertight.
Common questions

Frequently asked questions

Why does a water tank wall crack?

Because of concrete shrinkage, temperature changes and water pressure. If the crack reaches the reinforcement, the steel also starts to corrode.

Is it enough to paint over the crack?

No. It has to be opened, cleaned out and sealed in depth, then bridged with a reinforced waterproofing mortar that follows its small movements.

What about the joint between slab and wall?

It is the weakest point of almost every tank. It is routed, sealed and reinforced with a waterproof band so it stops leaking.

Is it suitable for drinking water tanks?

Yes, by choosing mortars and sealants certified for contact with drinking water. We state it in the specification.

Who carries out the work?

An approved applicator from our network, trained and approved by the system manufacturer. We handle the consulting, the specification and site management, and we guarantee the system is properly applied.

Do you work outside Catalonia?

Yes. We work throughout Spain, especially in Catalonia, the Valencia region and Aragon, with approved applicators in each area.

Do you manage tanks, ponds or pits with cracks or joints that leak?

We diagnose the cracks and joints, specify the repair, an approved applicator carries it out and we manage the work until watertightness is verified.

Request a technical study
Call WhatsApp Request a quote